The 4-in-1 ECM/Cluster Connection Interface DIUS–(4-tec) (kit) is designed to ensure the performance of certain operations provided in the diagnostic software BUDS and BUDS2, as well as for the convenience of servicing electronic modules ECM (ECU) using the DIUS4 software (DIUS System, DIUS Flasher).
In this one device, we have combined four:
- MPI-3 adapter for diagnosing all 4-TEC / E-TEC BRP 2002-2023 and newer vehicles.
- DESS 4-TEC/E-TEC Interface. Is designed for add/erase DESS keys for 4-TEC/E-TEC models.
- Power Interface Kit (analog of BRP p/n 515177223) – unit voltage stability during software updates. The 12 V Battery Power Supply Cable (analog of BRP p/n 529035997) is included.
- ECM/Cluster Connection Interface (ECCI) is designed for connections “on the table”.
Cable included:
- Bosch for ME17.8.5 and Cluster-1pcs
- Continental for M3C and Cluster-1 pcs
- Power Interface kit-1pcs
- Diagnostic Cable (p/n 710000851)- 1pcs
- 220V socket cable (power cable with EU plug included)-1 pcs
Is included
- BUDS license Megatech 10 yaers- 1 pcs -free
- BUDS 2 license Mechatronic expert test 3 days- 1 pcs-free
MPI-3 adapter can be used for diagnostic of all 4-TEC / E-TEC BRP vehicles 2002- and newest
Using the 4-in-1 DIUS- interface with ECA adapters you can connect the ECM and Cluster that are on your desk to your computer and perform the necessary maintenance without leaving home:
Restore the ECM after update crashes – ECM in Boot Mode (software DIUS);
Reprogram the ECM by stock or tuning firmware (software DIUS);
Change customer name;
Change cluster language;
Change cluster units;
Reset Maintenance Hours;
Change the VIN and Model numbers (Megatech/Mechatronic Expert privileges);
Add/erase DESS keys (Normal/Learning/Rental);
Enable/disable DESS system (Megatech/Mechatronic Expert privileges);
Change the Total Vehicle Hours (SeaDoo ECM Bosch) (Megatech/Mechatronic Expert privileges);
ECM/Cluster firmware updating;
Enable/disable vehicle’s options/modules/sensors (ACS, DPS, VTS, Depth Sounder, Lake Water Temp, Air Suspension, Belt protection, Fan, Electromechanical reverse, Supercharger, iS, iBr, Cruise+Slow Speed, Ski Mode, Altitude, VTS Switch, other options, modules and sensors) (Megatech/Mechatronic Expert privileges);
View Possible Causes and Service Actions;
View Faults Conditions (Speed, TPS, Intake PSI, Engine temp, Battery, Engaged Gear);
Read and Erase Active and Occurred Faults.
It must be remembered that when connecting the BUDS/BUDS2 to the ECM outside the vehicle, a lot of Active errors appears. This is due to the ECM being unable to detect the necessary sensors that are usually connected when the ECM is connected inside the vehicle. When the ECM will be connected back to the vehicle system, all these Active errors will become “Occurred” and will not affect the operation of the vehicle.
Powering.
The 4-in-1 DIUS- interface can be powered from a 220 volt outlet (power cable with EU plug is included) or from an external 12 volt battery connected to the 4-in-1 Interface using a 12 V Battery Power Supply Cable.
The build-in Power Interface and power supply cable allows the connection of a fully charged external battery to provide stable voltage to the ECM/Cluster and BUDS2.
Stable voltage is essential to prevent update crashes. DO NOT use a charger on the battery during software updates.
The 4-in-1 DIUS- interface connected to external battery can be used for extended diagnostic time.
The 4-in-1 DIUS- interface with or without the power supply cable will keep the ECM powered even if the ignition switch is turned off or the DESS key is removed.
The 4-in-1 DIUS- interface has a fuse protected voltmeter included and an extra fuse to protect from polarity inversion of the power supply cable.
“ECM/Cluster Adapter” (ECA)
Every adapter has a connector for a specific ECM model and 5 outputs (terminals) for connecting different types of Clusters.
At the moment we can offer cable for the following ECM models:
ECA-Bosch for ME17.8.5 and Cluster.
ECA-Continental for M3C and Cluster.
